Plumbing Basics: A Prerequisite for When Installing a Bathtub
Plumbing Basics: A Prerequisite for When Installing a Bathtub
Blog Article
Are you currently looking for information and facts about How to Install a Bathtub?
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately challenging task. If the old bathtub is readily available, the task can move immediately; if you have to open up a wall surface to get rid of the old tub as well as place the new tub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will need a helper to leave the old tub and also set in the brand-new one. See to it you have actually qualified on your own for the job and are comfortable attempting it. Instead of working with a professional to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Chances are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new bath tub in your bathroom if you have currently purchased a new tub and don't need to transform the arrangement of your previous water supply pipes.
Your tools as well as product checklist ought to comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be rather troublesome because of the restricted accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will come from the pipes. Once the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the tap in position with the producer given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind must be connected to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bath tub in the needed setting. The wood boards are useful in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit the bottom of the furthest flexible tap connector to the ideal supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill the bath tub as well as likewise check the overflow outlet and the normal outlet for leakages.
Finally, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub should wait until the bath tub has actually been made use of at least when as this will resolve it into its last position.
Planning for the Setup
Firstly, the supporting framework supplied with the bath should be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to split a rigid seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in problems with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealer can split rather early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about How to Install a Bathtub Yourself? Write a review below. We would be delighted to see your opinion about this blog post. In hopes to see you back again soon. If you appreciated our blog posting if you please make sure you remember to share it. Kudos for your time. Come back soon.
Act, don't delay! Report this page